Skyrc Cheetah 1/10 60A Sensored Combo Bedienungsanleitung PDF herunterladen

Thank you for purchasing Cheetah 1/10 CS60 60A Sensored ESC from SKYRC

TECHNOLOGY CO.,LTD. Please read the Instruction Manual thoroughly before you use the

product. These operating instructions are designed to ensure that you quickly become

familiar with its features and functions and make full use of this product.

INTRODUCTION

Never use faulty accessories, e.g. motor which may damage the ESC. Always insulate

exposed wiring with heat shrink tubing or electrical tape to prevent short circuits, which

can damage ESC too.

Always disconnect the battery pack from the speed control when not in use to avoid

short circuits and possible fire hazard. When the ESC is switched off, there is still small

current and it may cause over discharge of the battery after some time.

The ESC can support 4-9 cells NiMH or 2-3 cells LiPo battery.

SAFETY NOTE

It is not a toy and suitable for users older than 14 years old.

Never allow water, moisture, oil or other foreign materials to get inside ESC, motor, or on

the PC Boards. It may damage the ESC completely.

Never disassemble the ESC and modify the components on the PC Boards.

Suggest using the original wires and connectors which are packed in the box.

Never solder one part for more than 5 seconds as some components will get damaged

by high temperature.

Never run the ESC w/o load at full throttle and it may damage the bearings and other

moving parts.

Please make sure the location where to fix the ESC has good airflow ventilating so that

the heat could dissipate quickly.

To avoid short circuit, please keep the ESC connectors far away from other metal parts.

Never connect the battery in polarity in reverse.

Please remove the pinion gear before performing calibration and programming functions

with this system. Please keep your hands, hair, cloth, clear from the gear train and

wheels of an armed high performance

Before you switch on the ESC, please make sure all the cables are well solder with the

connectors (It is easy to get loose when running) . What's more, make sure the cables

not touch the moving parts.

Electronic motor timing will increase the temperatures of ESC and brushless motor. Use

extreme caution when setting up and testing your application to avoid overloading and

overheating.

Incorrect timing setting may cause permanent damage to the ESC and motors. Please

choose proper ratio and timing setting according to motor's instruction.

To avoid signal interference, please always turn on the transmitter first THEN turn on the

speed control. Do the opposite when powering it off.

We will not be responsible for any damage caused by non-compliance with above

instruction.

Note:

PREPARATION

Plan Speed Control Placement

Choose a location for the speed control that is protected from debris. To prevent radio

interference, place the speed control as far away from the radio receiver as possible and

keep the power wires as short as possible. Select a location that has good airflow

ventilating. If the ESC gets air flow, it will run cooler; and that means it will be more

efficient.

Mount Speed Control in Vehicle

Use double-sided tape to mount the speed control in vehicle (do not use CA glue). Use

double-sided tape to mount the switch where it will be easy to access. Select a position

where it will not get damaged or get switched OFF during a crash or roll-over.

Soldering

Cut the ESC's BLUE, YELLOW & ORANGE silicone motor power wires to the desired

length and strip about 3.2mm-6.35mm (1/8”-1/4”) of insulation from the end of each wire.

“Pre-tin”the wire by heating the end and applying solder until it is thoroughly covered.

CAUTION: By very careful not to splash yourself with hot solder.

Place the ESC's BLUE Phase ‘A’ motor wire onto motor's ‘A’ solder tab and solder. Use

soldering iron to apply heat to exposed wire; begin adding solder to tip of soldering iron

and wire. Add just enough solder to form a clean and continuous joint from the plated

area of the solder tab up onto the wire. Solder the ESC's YELLOW Phase‘B’ motor wire

to the motor's ‘B' solder tab and Solder the ESC's ORANGE Phase ‘C' motor wire to

motor’s ‘C’ solder tab.

Support Both Sensor or Sensor-less Brushless Motor

INSTRUCTION MANUAL

For 1/12 & 1/10 Scale Car

Connect the motor sensor harness to ESC. Insert the 6 pin connector on the end of the

motor's sensor wires into ESC's sensor harness socket.

Connect Throttle lead to ESC and other end to the Receiver (Throttle Channel, Ch2)

Connect the motor and the ESC.

Connect ESC to batter pack.

CONNECTION

Red power wire

(battery positive)

Black power wire

(battery negative)

Throttle

lead

Orange motor

phase wires

(phaseC)

Motor

Sensor Wire

Yellow motor

phase wires

(phaseB)

Blue motor

phase wires

(phaseA)

Power

Switch

Receiver

Program Card

ESC CALIBRATION

Calibration is necessary for the first use of the ESC, or whenever used with a new/different

transmitter. Individual transmitter's signals for full throttle, full brake and neutral vary. You

must calibrate your ESC so that it will operate more effectively with your transmitter.

How to calibrate the ESC?

ESC switch OFF.

Connect the ESC to the battery and the motor.

Turn on the transmitter.

Press and hold the ESC switch for few seconds, the motor will ring long beep once. After

that, the red LED will blink the motor will ring like beep-beep-beep… in a row which indicates

it is time to set the neutral position, full throttle and full brake one by one. You could release

the ESC switch now.

Keep the throttle trigger in neutral position, press the ESC switch once, the

green LED will blink once then extinguish and the motor will ring beep once

which indicates the neutral position has been set.

Hold full throttle and press the ESC switch once, the green LED will blink

twice then extinguish and the motor will ring twice like beep-beep which

indicates the full throttle has been set.

Move the throttle trigger to full brake and hold full brake, press the ESC

switch once, the green LED will blink three times then extinguish and the

motor will ring three times like beep-beep-beep which indicates the full brake

has been set.

After the calibration is finished, keep the throttle in neutral position, the red

LED will stay ON, the ESC and the motor is ready to work.

3/62/61/6

Battery

Pack

1 2

INSTRUCTION MANUAL 1
CAUTION: 2

Inhaltsverzeichnis

Seite 1 - INSTRUCTION MANUAL

Thank you for purchasing Cheetah 1/10 CS60 60A Sensored ESC from SKYRC TECHNOLOGY CO.,LTD. Please read the Instruction Manual thoroughly be

Seite 2 - CAUTION:

WARRANTY AND SERVICEThe Cheetah 1/10 CS60 60A Sensored ESC is guaranteed to be free from defects in materials or workmanship for a

Kommentare zu diesen Handbüchern

Keine Kommentare

Skyrc Cheetah 1/10 60A Sensored Combo Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Skyrc Cheetah 1/10 60A Sensored Combo herunter. SkyRC Cheetah 1/10 60A Sensored Combo User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Skyrc Cheetah 1/10 60A Sensored Combo